J-B Weld KwikWeld: A fast setting version of The Original Cold Weld two-part epoxy system that provides strong lasting repairs to multiple surfaces. Perfect for DIY household automotive marine craft repair and much more.

Feature:

• Contains 1oz. Each Steel and Hardener
• Bonds in 4 Minutes
• Easy to Use
• For Automotive and Industrial Use

Medium strength Threadlocker is an all purpose threadlocker ideal for all nut and bolt applications 6mm to 20mm. Threadlocker locks and seals while preventing parts from loosening due to vibration protects threads from corrosion and is removable with hand tools for easy disassembly. 6 ml tube Blue

Feature:

• Medium strength
• Seals threads against leakage
• Prevents rust and corrosion
• Temperature resistant to 300-degrees fahrenheit
• No Spill Drip or Clog Cap
• OEM Approved

Feature:

• Permanent Bond
• Crystal Clear
• Fast Grab - Holds in Just Seconds
• 100% Waterproof - for indoor/outdoor
• No-Run Formula
• Paintable
• Flexible
• Bonds: Metal Glass Fabric Wood Ceramic Leather Paper and More!

Feature:

• Heavy Duty Bond - Dries Permanent
• Easy to Use - Repositionable
• Clear Color - Non-Yellowing
• Indoor & Outdoor - Moisture Resistant
• Controlled Spray - Even Application
• Wide Pad Nozzle
• Meets New VOC Standard - <30% Mist Spray Adhesive
• Bonds - Wood Metal Fabric Foam Plastic Paper Glass Leather and More!

Sikaflex® 291 Fast Cure - White - 3oz Tube

Sikaflex® 291 is a 1-component, marine grade polyurethane elastomeric adhesive and sealant. Used by many boat builders, its fast cure time makes it ideal for applications where speed is important. Sikaflex® 291 is manufactured in accordance with IOS 9001/14001 quality assurance system and the responsible care program.

Features:

• General purpose polyurethane marine sealant
• Fast curing
• Above and below water applications
• Ideal for sealing thru hull and hardware applications
• Excellent adhesion to Gelcoat
• Resists saltwater

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 292i Marine Structural Bonding Compnent 10.3oz(300ml) Cartridge - White

Sikaflex-292i is a non-sag one component polyurethane adhesive of thixotropic, paste-like consistency which cures on exposure to atmospheric moisture to form a durable elastomer. Sikaflex-292i exhibits excellent adhesive properties and a high degree of mechanical strength. Sikaflex-292i meets the low spread of flame requirements set out by the International Maritime Organization (IMO).

Uses:
Sikaflex®-292i is suitable for structural joints in marine constructions which will be subjected to high dynamic stresses. Suitable to bond metals, particularly aluminum (including anodized finishes), metal primers and paint coatings (2-c systems), or ceramic materials, plastics such as GRP (unsaturated polyester resin), ABS, etc.

Characteristics & Advantages:

• Very Low VOC according to US EPA Method 24
• No added solvents
• Can be over-painted
• Capable of withstanding high dynamic stresses
• Vibration-damping
• Non-corrosive, Electrically non-conductive

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 295 UV - White - 3oz Tube

Features:

• UV resistant – no cracking or chalking
• Salt water resistant
• Good gap filling properties
• Fast tack-free time
• Paintable and sandable
• Bonds and seals in one step
• Non-yellowing

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SikaBiresin® AP112 + BPO Cream Hardener - White - Quart

Features:

• Structural bonding/repair system
• Fiber-filled for increased bonding strength
• For large scale repairs of broken FRP structures
• Easy to mix
• Excellent adhesive qualities

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikasil® N PLUS - Translucent - 3oz

Features:

• Bonds well to most substrates
• Fungicide additive for mildew resistance
• Excellent flexibility for dynamic joint movement
• Extremely long service life
• All season ease of application

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

These 1 in. x 1 in. Adhesive Backed Cable Tie Mounts when paired with cable ties allow you to neatly bundle and organize wires and cables along a wall or ceiling for a secure installation. Black. 100 per pack.

Feature:

• 1 .in x 1 .in
• Adhesive Backed
• Quantity: 100

Sikasil® N PLUS - White - 3oz

Features:

• Bonds well to most substrates
• Fungicide additive for mildew resistance
• Excellent flexibility for dynamic joint movement
• Extremely long service life
• All season ease of application

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 291 Fast Cure - Black - 3oz Tube 

Sikaflex® 291 is a 1-component, marine grade polyurethane elastomeric adhesive and sealant. Used by many boat builders, its fast cure time makes it ideal for applications where speed is important. Sikaflex® 291 is manufactured in accordance with IOS 9001/14001 quality assurance system and the responsible care program.

Features:

• General purpose polyurethane marine sealant
• Fast curing
• Above and below water applications
• Ideal for sealing thru hull and hardware applications
• Excellent adhesion to Gelcoat
• Resists saltwater

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

High Strength Threadlocker RED Gel Squeeze

OEM specified. Gel formula provides “liquid-reliability” without drips, globs, mess or waste. Available in three convenient sizes, the GEL TWIST™ pin-point applicator, the GEL SQUEEZE™ applicator, or the single-use pouch puts the Threadlocker right where you want it…on the part! High strength threadlocker for heavy-duty applications 3/8 inch to 1 inch (10mm to 25mm). Especially well-suited for permanently locking studs and press fits. Adds 3,000 PSI holding power on slip and press fit assemblies. Replaces set screws and snap rings. Locks against vibration loosening. May require heat or special tools for removal. Conforms to ASTM D5363 AN0221 (Mil-S-46163A, Type I, Grade K). 

Applications:

• Automobile - Suggested Applications: Cylinder block and rocker arm studs, ring gear bolts, frame bolts, shock absorber bolts; also ideal for vertical applications
• Heavy Duty - Suggested Applications: Cap screws and mounting studs on differentials

Directions:

Parts should be clean and oil free.

1. Remove protective cap.
2. Turn dial to expose 1/8″ to 1/4″ of material beyond tip.
3. Apply threadlocker to leading edge of male fitting,covering 5 to 6 threads. Avoid direct contact of tip to metal surface*.
4. Assemble parts and tighten to recommended torque.
5. Replace protective cap.*If contact occurs, expose 1/16” of material and wipe off with a clean towel.Temperature range: -65°F to 300°F (-54°C to 150°C).Refer to Technical Data Sheet for complete information.

NOTE: Permatex® Threadlocker Gel should not be used on plastic fittings. Do not use on food contact surfaces.Avoid food contamination during use and storage.

High Strength Threadlocker RED Bottle - 36ml

OEM specified. High strength threadlocker for heavy-duty applications 3/8 inch to 1 inch (10mm to 25mm). Especially well-suited for permanently locking studs and press fits. Adds 3,000 PSI holding power on slip and press fit assemblies. Replaces set screws and snap rings. Locks against vibration loosening. May require heat or special tools for removal. Conforms to ASTM D5363 AN0221 (Mil-S- 46163A, Type I, Grade K). 

Applications:

• Automobile - Suggested Applications: Cylinder block and rocker arm studs, ring gear bolts, frame bolts, shock absorber bolts
• Motorcycle - Suggested Applications: All engine mounting bolts
• Heavy Duty - Suggested Applications: Air starter fasteners, suspension fasteners, shock absorber mounts, wheel studs, exhaust system mounts, bumper fasteners
• Marine - Suggested Applications: Cylinder block studs, ring gear bolts, frame bolts, shock bolts

Directions:

1. Clean and dry parts using Permatex® Surface Prep™activator.
2. Apply to both parts (threaded areas) and assemble. Refer toTechnical Data Sheet for complete information.

NOTE: High Strength Threadlocker works on metal parts. It is not recommended for plastics. Cured High Strength Threadlocker must be heated to 500°F (260°C)before parts will separate.

Insta Set|TM| Accelerator is for use after joining parts with Cyanoacrylate adhesives and fully cures in 8 seconds. 100 Percent compatible with plastic and foam. 2 oz.

Feature:

• Adhesive / Glue Installation Accessory
• For use with Cyanoacrylate adhesives to fully cure in 8 seconds
• 100 Percent compatible with plastic and foam
• 2 oz.

A higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds.

Feature:

• Gap-filling adhesive
• 5-15 second glue
• Insta-Cure Cyanoacrylate adhesive
• Cure time can be expedited using Insta-Set accelerator

Clean several types of reactive adhesives from a variety of substrates quickly and efficiently with the 3M General Purpose Adhesive Cleaner. This cleaner can effectively remove silicone polish tar oil epoxies tree sap light paint overspray bugs urethane wax and other stubborn adhesives from the surface. Containing a blend of many solvents this adhesive cleaner is specially formulated not to harm properly cured automotive paint fabrics or vinyl when used as directed.

Feature:

• 1-quart can
• Specially blended solvent
• Provides easy cleanup of most types of adhesives
• Will not cause any damage to dry paints

SikaBiresin® CR72 - Pale Amber - 1 Gallon

Applications:

• High performance marine boats, parts, and tooling applications
• Suitable for wet layup, vacuum-bagging, infusion 

Features:

• Epoxy lamination system
• Low viscosity for excellent wet-out
• Three hardener choices: SikaBiresin® CH72-1 (Fast), SikaBiresin® CH72-2 (Medium), SikaBiresin® CH72-3 (Slow)
• UV resistant
• Above or below waterline applications
• RoHS and REACH compliant
• Non-styrene
• Excellent bond to all fabrics
• Suitable for aramid fiber laminates

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SikaBiresin® CH72-1 Fast Cure - Pale Amber - Quart

Applications:

• High performance marine boats, parts, and tooling applications
• Suitable for wet layup, vacuum-bagging, infusion 

Features:

• Epoxy lamination system
• Low viscosity for excellent wet-out
• Three hardener choices: SikaBiresin® CH72-1 (Fast), SikaBiresin® CH72-2 (Medium), SikaBiresin® CH72-3 (Slow)
• UV resistant
• Above or below waterline applications
• RoHS and REACH compliant
• Non-styrene
• Excellent bond to all fabrics
• Suitable for aramid fiber laminates

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SikaBiresin® CH72-2 Medium Cure - Pale Amber - Quart

Applications:

• High performance marine boats, parts, and tooling applications
• Suitable for wet layup, vacuum-bagging, infusion 

Features:

• Epoxy lamination system
• Low viscosity for excellent wet-out
• Three hardener choices: SikaBiresin® CH72-1 (Fast), SikaBiresin® CH72-2 (Medium), SikaBiresin® CH72-3 (Slow)
• UV resistant
• Above or below waterline applications
• RoHS and REACH compliant
• Non-styrene
• Excellent bond to all fabrics
• Suitable for aramid fiber laminates

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SikaBiresin® CH72-3 Slow Cure - Pale Amber - Quart

Applications:

• High performance marine boats, parts, and tooling applications
• Suitable for wet layup, vacuum-bagging, infusion 

Features:

• Epoxy lamination system
• Low viscosity for excellent wet-out
• Three hardener choices: SikaBiresin® CH72-1 (Fast), SikaBiresin® CH72-2 (Medium), SikaBiresin® CH72-3 (Slow)
• UV resistant
• Above or below waterline applications
• RoHS and REACH compliant
• Non-styrene
• Excellent bond to all fabrics
• Suitable for aramid fiber laminates

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.