Spanner Wrench/Deck Plate Key 

Features:

• Cast bronze with stainless steel pins to fit 1/4" and 5/16" holes. 

• Opens to service deck plates or strainer caps with key holes up to 7" apart. 
• Hangs conveniently near the strainer(s) location. 
•  C83600 bronze

• Square Mixing Tip
  
• 4" Long
  
• Case of 10

8040 Acrylic Adhesive with Plunger 

CANNOT SHIP AIR - UPS GROUND ONLY

AT-8040 is a good general purpose adhesive packaged in a manual plunger cartridge. Simply snip off the two end caps and dispense the needed amount of adhesive onto a clean surface and mix it by hand. AT-8040 cures in 10-12 minutes, has a 6 minute working time and develops working strength in 40 minutes. AT-8040 has a 12 month shelf life when stored at 72°. Weld Mount recommends that where ever possible this adhesive be refrigerated. Packaged in a 30ml cartridge this adhesive does not require the adhesive gun or mixing tips. The 30ml cartridge will bond 30-50 parts.

Stainless Steel Bottle Opener with Brushed Finish 

Corrosion resistant investment cast 316 stainless steel bottle opener wall mounts with two #6 FH fasteners (not included).

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

• AT-8040 Adhesive
  
• (25) Pieces AT-5 White Tie Mount
  
• (1) Plastic Mixing Sheet
  
• (2) Mixing Sticks
  
• Complete step-by-step instructions

Plastic Suction Cup Handle

Injection Molded Nylon/Nitrile-Buna Rubber 

Portable, dual suction cup handle installs instantly. Mounts in any direction on any non-porous surface. Easily mount and re-mount with no marks or damage to hull. No holes, screws, or tools required. Ideal for cleaning waterlines or boat bottoms while swimming or from a dinghy. Attach to your paddleboard or kayak for an extra handle during transport. For use above or below the waterline. Constructed of non-corrosive injection molded nylon and Nitrile-Buna rubber. Designed to assist grip not to leverage full body weight.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Add-A-Snap - White - 1-1/2" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

• Square Mixing Tip
  
• 4" Long
  
• Case of 50

Thru-Hull Installation Tool 

Thru Hull Installation Tool

The Concept:

THT-530 makes the installation of standard GROCO thru-hull fittings possible by a single installer.  Slide the thru-hull fitting, flanged end first, over the tool.  (It will stop at the proper step.)  Tie a length of monofilament to the eye and place it into the already-cut hole in the hull of the boat.  Apply caulking to the flange of the fitting, and pull the fitting through the hole and against the hull from inside the boat.  Thread the mono-filament through the locknut or seacock. With the fitting pulled firmly against the hull the locknut or the seacock may be screwed onto the fitting.

THT-530 fits GROCO Thru-hull Fitting Sizes from 1/2" through 3"

Add-A-Snap - Black - 1-1/2" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.