NONMETALLIC SHEATHED CABLE CONNECTOR
Clamp type
Die-cast zinc
Use in dry locations
Use with a box or an enclosure
Cable size - 2 #14 & #10 or
3 #14 or #12 without ground
2711 1/2 IN. CLAMP TYPE CONNECTOR
SIZE:1/2"
|
CONDUIT BODY - TYPE C
For non-metallic schedule 40/80 conduit
Type: C
Used as a connector in straight line -
installations
This allows access for wire pulling and -
limited wire splices as allowed by NEC
5133101U 1/2 IN. TYPE C COND BODY
SIZE:1/2"
|
PVC CONDUIT CLAMPS
Molded PVC conduit clamp
U-shaped conduit support device
Anchors conduit to interior/exterior surfaces
2 holes in feet for mounting with screws/nails
5133738B 1 IN. CONDUIT CLAMP
SIZE:1"
QTY/PACK:5 / Bag
|
CONDUIT BODY TYPE LR
For non-metallic schedule 40/80 conduit
Type: LR
Used for 90 deg. direction change of conduit run
Rectangular shaped conduit body-removable cover
Two conduit hubs; one facing the cover side with-
the end wall hub pointing up. other hub is in-
the right hand side wall at opposite fitting end
5133654U 1 1/2 IN. T/LR COND BODY
SIZE:1-1/2"
|
SINGLE GANG IN-USE WEATHERPROOF COVER
Outlet, switch or plug protection from rain, -
sleet or snow
Covers are molded of clear UV stabilized -
polycarbonate & can be hinged from top or side
Provide for vertical or horizontal use
Single gang includes 3 patented rotating -
inserts to provide 14 application configurations
Use in wet location when cover is closed
5133694 HORZ/VERT SINGLE
DEPTH:3-1/8"
COLOR:
|
ROUND BLANK COVER
4" diameter
Use for 4/0 applications
EZYKLR 4 IN. ROUND BLANK COVER
SIZE:4"
|
STRAIGHT CONDUIT FITTING
Liquidtight
For nonmetallic fitting
6441001C 1/2 IN. CONDUIT FITTING
SIZE:1/2"
|
DOUBLE DUPLEX COVER
Weatherproof when closed
Covers two standard 115 volt duplex receptacles
Fits two gang FS type outdoor box
5133347B DOUBLE DUPLEX COVER
|
STANDARD UL PVC COUPLING
Connector used to join spigot (plain) ends-
of lengths of conduit pipe
Fitting consists of two solvent weld female -
ends with a center stop
Both pieces of pipe should seat at the stop -
for proper positioning
Conforms to NEMA TC-3 and UL 514
6141624U 3/4 IN. PVC COUPLING
SIZE:3/4"
COLOR:Gray
|
STANDARD UL PVC COUPLING
Connector used to join spigot (plain) ends-
of lengths of conduit pipe
Fitting consists of two solvent weld female -
ends with a center stop
Both pieces of pipe should seat at the stop -
for proper positioning
Conforms to NEMA TC-3 and UL 514
6141625C 1 IN. PVC COUPLING
SIZE:1"
|
90 DEGREE SCHEDULE 40 ELBOW
Offers 90 deg. direction change in conduit run
Use with Schedule 40 non-metallic fittings
Both ends are spigot (plain) & solvent weld
Will not rust or corrode
Can be used above ground or buried and is-
suitable for concrete encasement
Conforms to NEMA TC-3 and UL 514
5133824U 3/4 IN. PVC 90 DEG ELBOW
SIZE:3/4"
|
To support EMT conduit where greater load bearing is required. Indoor or outdoor applications.
Size In=1-1/4
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed.
Size In=2
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
45 DEGREE SCHEDULE 40 ELBOW
Use with Schedule 40 non-metallic fittings
Both ends plain
Will not rust or corrode
Can be used above ground or buried and is-
suitable for concrete encasement
Conforms to NEMA TC-3 and UL 514
5133765U 1 IN. SCH40 45 DEG ELBOW
SIZE:1"
|
SCHEDULE 40 MALE X FEMALE REDUCER
Special application fittings
For non-metallic schedule 40/80 conduit
Male x Female
5142221C 1 IN. X3/4 IN. REDUCER
SIZE:1"x 3/4"
|
CONDUIT BODY TYPE LL
For non-metallic schedule 40/80 conduit
Type: LL
Used for a 90 deg. direction change of conduit
Rectangular shaped conduit body-removable cover
Contains two conduit hubs; one facing the cover-
side with the end wall hub point up
Other hub is in the left hand side wall at the-
opposite end of the fitting
5133662U 1 IN. TYPE LL CONDT BODY
SIZE:1"
|
PVC CONDUIT CLAMPS
Molded PVC conduit clamp
U-shaped conduit support device
Anchors conduit to interior/exterior surfaces
2 holes in feet for mounting with screws/nails
5133735B 2 IN. CONDUIT CLAMP
SIZE:2"
QTY/PACK:5 / Bag
|
CONDUIT BODY - TYPE T
For non-metallic schedule 40/80 conduit
Type: T
5133564U 3/4 IN. TYPE T COND BODY
SIZE:3/4"
|
CONDUIT BODY - TYPE T
For non-metallic schedule 40/80 conduit
Type: T
5133568U 2 IN. TYPE T CONDUT BODY
SIZE:2"
|
45 DEGREE SCHEDULE 40 ELBOW
Use with Schedule 40 non-metallic fittings
Both ends plain
Will not rust or corrode
Can be used above ground or buried and is-
suitable for concrete encasement
Conforms to NEMA TC-3 and UL 514
5133764U 3/4 IN. PVC 45DEF ELBOW
SIZE:3/4"
|
EMT TO BOX PULL ELBOW
Without gasket
Connect EMT conduit to metal box at 90 degree bend
Zinc die cast
Set-screw type
Removable aluminum cover facilitates wire pulling
Die cast locknut provided
UL listed
14305 1/2 IN. EMT TO BX PULL ELBOW
SIZE:1/2"
|
Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL
Listed, RoHS Compliance.
Size In=1-1/4
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
ACCESS FITTING TYPE LB
For non-metallic schedule 40/80 conduit
Type: LB
Use for a change of direction of the conduit run
With the back hub usually exiting thru a wall
Rectangular shaped conduit body
Removable cover
One entrance hub is in one end wall of fitting-
the other hub is at opposite end in the back
5133664U 3/4 IN. TYPE LB CON BODY
SIZE:3/4"
|
90 DEGREE SCHEDULE 40 ELBOW
Offers 90 deg. direction change in conduit run
Use with Schedule 40 non-metallic fittings
Both ends are spigot (plain) & solvent weld
Will not rust or corrode
Can be used above ground or buried and is-
suitable for concrete encasement
Conforms to NEMA TC-3 and UL 514
5133825U 1 IN. PVC 90 DEG ELBOW
SIZE:1"
|
PVC Conduit Heating Blankets Up to 1-1/2" - Our great PVC Heating Blankets make bending a breeze.PVC Conduit Heating Blankets Up to 1-1/2" features include:
Below is more info on our PVC Conduit Heating Blankets Up to 1-1/2"- Capacity: Up to 1-1/2"Size: 13" x 8-1/4" Wattage: 2 This item does not ship to APO/FPO addresses. |
Right Angle Nylon Cable Glands NPT Thread 1-1/4"- - These Right Angle Cable Glands are corrosion resistant.Nylon Cable Glands - NPT Thread - 90° 1-1/4"- features include:
Below is more info on our Nylon Cable Glands - NPT Thread - 90° 1-1/4" NPT Thread: 1-1/4"Cable Range: .87-1.14 Bag Qty: 1 This item does not ship to APO/FPO addresses. |
Malleable Rigid 3-Piece Couplings 2-1/2" - Malleable Rigid 3-Piece Couplings are Used to Join 2 lengths of Threaded Conduit when Neither Can Be Rotated.Malleable Rigid 3-Piece Couplings 2-1/2" features include:
Below is more info on our Malleable Rigid 3-Piece Couplings 2-1/2" Fitting Type: Rigid Malleable 3-Piece CouplingTrade Size: 2-1/2" Box Qty: 1 This item does not ship to APO/FPO addresses. |
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed.
Size In=1-1/2
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
SWIVEL LOK MULTI-POSITION CONNECTOR
For type B conduit nonmetallic conduit
Use in dry or wet locations
Gray nonmetallic construction
Includes neoprene O-ring and nylon gasket
Twists from 0: to 90:
Individually poly bagged
UL listed and CSA approved
4733-8 3/4 IN. LQD TITE CONNECTOR
SIZE:3/4"
|
ACCESS FITTING TYPE LB
For non-metallic schedule 40/80 conduit
Type: LB
Use for a change of direction of the conduit run
With the back hub usually exiting thru a wall
Rectangular shaped conduit body
Removable cover
One entrance hub is in one end wall of fitting-
the other hub is at opposite end in the back
5133665U 1 IN. TYPE LB COND BODY
SIZE:1"
|
PVC FEMALE ADAPTER
Connector used to transition threaded metal-
conduit to PVC conduit or join PVC to PVC
Has two female ends, one threaded the -
other is solvent weld
Conforms to NEMA TC-3 and UL 514
5140044C 3/4 IN. FEMALE ADAPTER
SIZE:3/4"
|
PVC TERMINAL ADAPTER
Adapting non-metallic conduits to boxes
Threaded fittings
Metallic systems
Male threads on one end, socket on other
5140107C 1 1/2 IN. TERMNL ADAPTER
SIZE:1-1/2"
|
|
|
|
|
Copyright © 1999-2018 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |