Items 1- 32 of 195 total

Sport Bar Fire Extinguisher Holder, Black, 55-14 Jeep CJ and Wrangler Sport Bar Fire Extinguisher Holder, Black, 55-14 Jeep CJ and Wrangler
Online
$21.64 for EA
Retail $29.99
Mfr PN: 13305.21
Stock: 9
Special designed holder incorporates thick nylon web straps that secures your Fire Extinguisher to the roll bar. Straps are fully adjustable and secure with hook and loop fasteners and will hold up to a 4 diameter fire extinguisher. Fits up to a 3 roll bar with or without padding.
Online
$21.64 for EA
Retail $29.99
Mfr PN: 13305.21
Stock: 9

GM 8.5in. 10 Bolt Rear High Capacity Cover GM 8.5in. 10 Bolt Rear High Capacity Cover
Online
$294.66 for EA
Retail $434.60
Mfr PN: GM10-8.5
Stock: 6
Mag-Hytec's heavy duty differential covers and transmission pans provide increased lubricant and cooling capacity for hard working recreational and service vehicles. Mag-Hytec covers and pans set your vehicle apart in both aesthetics and function cast in A356-T6 aluminum and texture powder coated black With machined cooling fins. Magnetic drain plugs trap worn gear material promoting fluid integrity. Each unit is fitted with ARP 568 O-rings for superior sealing. All hardware is 303 stainless steel, in most applications no gasket or sealant is required, and all Mag-Hytec parts are covered by a lifetime limited warranty. Depend on Mag-Hytec when you're pulling a heavy load. For Use On GM 8.5in./8.6in. Rear Axles Only Finned Aircraft Aluminum Housing For Improved Cooling Black Powder Coat Finish Holds 2 Extra Quarts Of Oil Overall Height Is 3 1/4in. Offers Easy Routine Maintenance Without Removing The Differential Cover Dipstick With Magnetic Insert
Online
$294.66 for EA
Retail $434.60
Mfr PN: GM10-8.5
Stock: 6

DANA 44 DIFF COVER DANA 44 DIFF COVER
Online
$120.12 for EA
Mfr PN: 42-11-044
Stock: 280
Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the most punishing rocks and trail hazards. The stock covers your Jeep came with are weak, stamped sheetmetal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, not to mention a difficult, messy trail fix. Even more common, though less catastrophic, is "peel back" that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment. The Bombshell Diff Cover is your best insurance against each of these hazards. The Bombshell differential cover is cast from highly ductile nodular iron—the same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick & up to 1" thick—cross-section around the bolt ring, where contact with the rocks is most likely. Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16" to a brutal 1/2" thick at the outermost surface.
Online
$120.12 for EA
Mfr PN: 42-11-044
Stock: 280

Roll Bar Mounted Fire Extinguisher Holder - 2.5lb. Roll Bar Mounted Fire Extinguisher Holder - 2.5lb.
Online
$20.99 for EA
Mfr PN: 769540
Stock: 1288
This handy 2.5 pound fire extinguisher holder will keep your extinguisher stored safely and securely to your off-road rig's 2-3 inch roll bar and off of the floorboard during dicey off-road driving conditions. Use with 1.5-4 inch Sport/Roll Bar Attaches using heavy-duty hook and loop straps Works with 2.5 pound Fire Exinguishers Available in black only
Online
$20.99 for EA
Mfr PN: 769540
Stock: 1288

C-PILLAR KIT C-PILLAR KIT
Online
$179.98 for EA
Mfr PN: 18-18-030
Stock: 5
For those looking to further enhance the JK 4-Door Trail Cage installation, the Poison Spyder C-Pillar Kit ads strength to the rear passenger portion of the OE cage. This kit must be welded in to the OE cage at the top, but it bolts in at the lower end. The C-Pillar kit consists of CNC laser cut lengths of 1.75" OD, .120" wall DOM tubing, and engineered foot plates that are fabricated from CNC laser cut, brake-formed 3/16" plate steel. Convenient indexing tabs and slots are provided where the DOM tube connects with the foot plate, making assembly quick and easy.
Online
$179.98 for EA
Mfr PN: 18-18-030
Stock: 5

Tube Clamps Tube Clamps
Online
$43.20 for EA
Mfr PN: 180127-KIT
Stock: 5
Trail-Gear O.D. Tube Clamps are ideal for suspension and steering brackets that you need attached to a section of tubing when you don’t want to weld the bracket directly to the tubing because adjustment or frequent removal of the bracket is needed. The O.D. Tube Clamp is perfect for attaching shock brackets to suspension link or steering brackets to steering rods or links and allows you to attach steel mounting brackets that are readily available to aluminum suspension links and steering rods that you could not otherwise weld steel brackets to. Manufactured from 1020 steel, with a clamping force of up to 8,600lbs these tube clamps will not fail even under the most extreme circumstances. Sold Individually.
Online
$43.20 for EA
Mfr PN: 180127-KIT
Stock: 5

GUSSET TRIANGLE CUTOUT GUSSET TRIANGLE CUTOUT
Online
$3.38 for EA
Retail $5.99
Mfr PN: 120086-KIT
Stock: 1
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
Online
$3.38 for EA
Retail $5.99
Mfr PN: 120086-KIT
Stock: 1

GUSSET TRIANGLE BLANK GUSSET TRIANGLE BLANK
Online
$3.38 for EA
Retail $5.99
Mfr PN: 120087-KIT
Stock: 2
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
Online
$3.38 for EA
Retail $5.99
Mfr PN: 120087-KIT
Stock: 2

Ford 8.8in. Aluminum Cover Ford 8.8in. Aluminum Cover
Online
$129.99 for EA
Mfr PN: 40-2013AL
Stock: 64
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Ford 8.8in. Rear Axles Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$129.99 for EA
Mfr PN: 40-2013AL
Stock: 64

Interlocking Tube Clamps Interlocking Tube Clamps
Online
$38.82 for EA
Mfr PN: 180114-KIT
Stock: 5
Need to place a support tube across your truggy or buggy, but need the flexibility to remove a motor, transmission, or even a seat? We have the perfect solution for you, Trail-Gear’s Interlocking Tube Clamps. They are machined from 100% 4130 Chromoly and use a counter sunk allen head screw.
Online
$38.82 for EA
Mfr PN: 180114-KIT
Stock: 5

FIRE EXTINGUISHER MOUNT FIRE EXTINGUISHER MOUNT
Online
$70.14 for EA
Retail $74.99
Mfr PN: FIREX-MNT-DOR
Stock: 36
NHRA approved, the Drake Fire Extinguisher Mount is machined from 6061-T6 billet aluminum with a black anodized finish and a laser etched logo. Features include a red anodized quick release knob, and a versatile mounting options. Fits various sizes of automobile fire extinguishers. Requires part number DRKFIRE-CLMP-S-DOR or DRKFIRE-CLMP-L-DOR.
Online
$70.14 for EA
Retail $74.99
Mfr PN: FIREX-MNT-DOR
Stock: 36

Trail Gear Gusset, Web 120083-KIT Trail Gear Gusset, Web 120083-KIT
Online
$3.38 for EA
Retail $5.99
Mfr PN: 120083-KIT
Stock: 11
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
Online
$3.38 for EA
Retail $5.99
Mfr PN: 120083-KIT
Stock: 11

3" Diameter Fire Extinguisher Mount Clamp 3" Diameter Fire Extinguisher Mount Clamp
Online
$20.46 for EA
Retail $21.99
Mfr PN: FIRE-CLMP-L-DOR
Stock: 8
Clamps for use with FIREX-MNT-DOR.
Online
$20.46 for EA
Retail $21.99
Mfr PN: FIRE-CLMP-L-DOR
Stock: 8

Paracord Grab Handle û Roll Bar Paracord Grab Handle û Roll Bar
Online
$60.37 for EA
Mfr PN: TAOGHUPBU
Stock: 43
The Paracord Grab handles are made from the same cord material that you can find on parachutes. The material is woven into a tough looking grab hand and will fit padded or non-padded roll bars. They have metal hardware and a griping backing so that they stay put when you’re pushing the vehicle to the limits. Trek Armor has over 17 years of combined experience in manufacturing cutting and sewing products for the U.S. military, you can be sure that what we produce is absolutely top of the line.
Online
$60.37 for EA
Mfr PN: TAOGHUPBU
Stock: 43

466227 2.6# EXTINGUISHER 466227 2.6# EXTINGUISHER
Online
$37.13 for 1 EA
Retail $50.99
Mfr PN: 466227
Stock: 14
PRO MULTI-PURPOSE FIRE EXTINGUISHER UL Rate 1-A:10-B:C dry chemical multi-purpose - fire extinguisher with easy to pull safety pin Pressure gauge provides at a glance status Tough impact resistant metal valve, handle - and lever with powder coated aluminum cylinder Suitable for use on most common fires Contains 2.6 lb. average Monoammonium Phosphate Supplied with wall hanger for fast access 466227 2.6# EXTINGUISHER COLOR:Red
Online
$37.13 for 1 EA
Retail $50.99
Mfr PN: 466227
Stock: 14

Dana 44 Aluminum Cover Dana 44 Aluminum Cover
Online
$129.99 for EA
Mfr PN: 40-2033AL
Stock: 326
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Dana 44 Front Or Rear Asxles Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$129.99 for EA
Mfr PN: 40-2033AL
Stock: 326

DANA 30 DIFF COVER - PC DANA 30 DIFF COVER - PC
Online
$132.10 for EA
Mfr PN: 42-11-030-PC
Stock: 314
Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the most punishing rocks and trail hazards. The stock covers your Jeep came with are weak, stamped sheetmetal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, not to mention a difficult, messy trail fix. Even more common, though less catastrophic, is "peel back" that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment. The Bombshell Diff Cover is your best insurance against each of these hazards. The Bombshell differential cover is cast from highly ductile nodular iron—the same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick & up to 1" thick—cross-section around the bolt ring, where contact with the rocks is most likely. Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16" to a brutal 1/2" thick at the outermost surface.
Online
$132.10 for EA
Mfr PN: 42-11-030-PC
Stock: 314

Dana 25/27/30 Aluminum Cover Dana 25/27/30 Aluminum Cover
Online
$119.99 for EA
Mfr PN: 40-2031AL
Stock: 235
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Dana 25/27/30 Front Axles Except KJ Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$119.99 for EA
Mfr PN: 40-2031AL
Stock: 235

Dana 35 Aluminum Cover Dana 35 Aluminum Cover
Online
$129.99 for EA
Mfr PN: 40-2049AL
Stock: 166
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Dana 35 Rear Axles Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$129.99 for EA
Mfr PN: 40-2049AL
Stock: 166

Classic Fairway Golf Cart Seat Blanket/Cover - Houndstooth Classic Fairway Golf Cart Seat Blanket/Cover - Houndstooth
Online
$39.98 for Each
Retail $75.00
Mfr PN: 40-027-015701-00
Stock: 153
Classic Accessories Golf Cart Seat Blanket (Houndstooth), is instant protection from hot, cold or dirty golf car seats! The Classic Accessories Fairway Golf collection features quilted water-resistant blanket made of heavy-duty fabric for durable performance, allowing you to focus on the game, not the forecast. This blanket feature: Quilted top with plush fleece backing and reflective piping, Wipe-clean, water-resistant, heavy-duty fabric. Quickly secures over golf cart arm rests. Also great as a lap blanket which self-packs for easy transport Exterior pocket offers storage and placement for personalized embroidery. Fleece thumb tab. Machine washable. One size fits most two-person golf cart seats with armrests. We Cover Your Gear!
Online
$39.98 for Each
Retail $75.00
Mfr PN: 40-027-015701-00
Stock: 153

TRANSMISSION SKID PLATE TRANSMISSION SKID PLATE
Online
$143.99 for EA
Retail $155.99
Mfr PN: REA1013
Stock: 118
Rubicon Express has everything you need to protect the vulnerable undercarriage of your 07+ Jeep Wrangler JK from front to back, with skid plates for your engine oil pan, transfer case, and fuel tank. All of the skidplates are CNC laser cut from 3/16-inch steel to withstand even the worst abuse, and are designed to mount up tight to the drivetrain to maximize ground clearance. The modular protection system allows you to add skidplates as your needs and budget allow without any concerns about compatibility.
Online
$143.99 for EA
Retail $155.99
Mfr PN: REA1013
Stock: 118

ROLL BAR RAPZ PAIR BLACK ROLL BAR RAPZ PAIR BLACK
Online
$30.65 for EA
Mfr PN: 12501
Stock: 106
Neoprene Roll Bar Wrap; 2 x 50in lengths; Roll bar Rapz are a neoprene-backed wrap with "hook-and-loop" fasteners. Rapz are designed to wrap around or cover up almost any round or square tube item. This product can not be returned.
Online
$30.65 for EA
Mfr PN: 12501
Stock: 106

Paracord Grab Handle - Roll Bar Paracord Grab Handle - Roll Bar
Online
$60.37 for EA
Mfr PN: TAOGHUPBB
Stock: 105
The Paracord Grab handles are made from the same cord material that you can find on parachutes. The material is woven into a tough looking grab hand and will fit padded or non-padded roll bars. They have metal hardware and a griping backing so that they stay put when you’re pushing the vehicle to the limits. Trek Armor has over 17 years of combined experience in manufacturing cutting and sewing products for the U.S. military, you can be sure that what we produce is absolutely top of the line.
Online
$60.37 for EA
Mfr PN: TAOGHUPBB
Stock: 105

Roll Bar Light Roll Bar Light
Online
$15.90 for EA
Retail $17.99
Mfr PN: 769801
Stock: 80
Most Jeeps are not known for their interior lighting. Remedy that problem with Rampage's Roll Bar Light. It attaches around any 2-3" bar using hook and loop fasteners. There is no wiring involved, it uses 3 AAA batteries (not included) and will stay bright for hundreds of hours and the LEDs are long lasting. Universal application Super bright LED light Fastens with hook and loop fasteners Wireless Stays bright for hundreds of hours
Online
$15.90 for EA
Retail $17.99
Mfr PN: 769801
Stock: 80

Dana 44 Iron RedCover Dana 44 Iron RedCover
Online
$207.44 for EA
Retail $302.94
Mfr PN: 750003
Stock: 80
When off road, it is inevitable that obstacles and off road hazards will be encountered that could potentially inflict expensive damage to your differential. to prevent this, ARB manufactures the differential cover. Using high tensile nodular iron, it has been engineered to protect the differential and ring and pinion set from any off road hazards. Features: Computer optimized cross brace design increases the structural rigidity of the whole axle. Additional housing strength helps keep the ring & pinion gears meshing on the flat faces of the teeth, greatly increasing ring & pinion life and overall maximum load strength. Top quality, high power neodymium magnets are used in both the Drain Plug and the dipstick to collect metallic wear particles as the vehicle moves. Magnet location in the end of the dipstick allows the oil to be checked For tell-tale signs of Internal damage. For Use On Dana 44 Front Or Rear Axles Super Thick Cast Nodular Iron Bright Red Powder Coat Finish Magnetic Drain Plug Magnetic Dip Stick Includes Mounting Hardware
Online
$207.44 for EA
Retail $302.94
Mfr PN: 750003
Stock: 80

MOLLE ROLL BAR PAD MOLLE ROLL BAR PAD
Online
$133.99 for EA
Mfr PN: 5665101
Stock: 73
MOLLE attachment points in front, center and rear sections to allow install of MOLLE-style pouches. Double layer stitching with highest quality, UV protected and rot-resistant thread.
Online
$133.99 for EA
Mfr PN: 5665101
Stock: 73

SRC CAGE KIT 6 PIECE SRC CAGE KIT 6 PIECE
Online
$669.99 for EA
Retail $747.99
Mfr PN: 76902
Stock: 68
The all new reinforced cage kits come with everything you'll need to strengthen your factory roll bar into a solid foundation if a roll over takes place. We start off with 1020 .120 Wall DOM tubing which is one of the strongest materials available. Each kit includes the new Knuckle System that attaches to the factory roll bar, using a unique pivot and fastening point on one end and grade 10 fasteners on the other. Making it one of the strongest and the most solid mounts available for your Jeep®.
Online
$669.99 for EA
Retail $747.99
Mfr PN: 76902
Stock: 68

Dana 50/60/70 Aluminum Cover Dana 50/60/70 Aluminum Cover
Online
$129.99 for EA
Mfr PN: 40-2034AL
Stock: 68
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Dana 50/60/70 Front Or Rear Axles Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$129.99 for EA
Mfr PN: 40-2034AL
Stock: 68

JK TRAIL GATE JK TRAIL GATE
Online
$586.28 for EA
Mfr PN: 17-66-010
Stock: 67
JK TRAIL GATE
Online
$586.28 for EA
Mfr PN: 17-66-010
Stock: 67

FIRE EXTINGUISHER HOLDER FIRE EXTINGUISHER HOLDER
Online
$32.38 for EA
Mfr PN: 57-62-110
Stock: 59
The velcro straps that hold this unit to the roll bar are optimally sized for use on padded roll bars. When using on bare, un-padded tubes (1.75" OD or larger recommended), the ends of the velcro straps wlll be too long, but can either be tucked in or cut off (use a lighter to cauterize the cut edge of the nylon webbing).
Online
$32.38 for EA
Mfr PN: 57-62-110
Stock: 59

TIE BAR TIE BAR
Online
$22.65 for EA
Mfr PN: 97510-22
Stock: 57
TIE BAR
Online
$22.65 for EA
Mfr PN: 97510-22
Stock: 57

HARDWARESET FOR 76902 HARDWARESET FOR 76902
Online
$24.05 for EA
Mfr PN: 76902HDW
Stock: 54
HARDWARESET FOR 76902
Online
$24.05 for EA
Mfr PN: 76902HDW
Stock: 54