FLUSH 'N' SPARKLE REFILL CARTRIDGES Safe to handle without gloves Replace every 3 months or when color disappears 2 per card 8102P8 FLUSH-N-SPARKLE REFILL

HYDRANT PARTS KIT For C series bury hydrants Contains the following: G20 - Draw straps (Per Pr.) G25 - Pivot connector & nuts G30 - Packing nut G35 - Valve stem packing A115 - Plunger PKCF PARTS KIT/C1000 HYDRANT

POW-R WRAP+ - Industrial Strength, Water Activated Fibreglass Tape, Pipe & Hose Repair Kit - 4" x 360" suitable for pipes up to 12"

The complete kit includes:
= A sealed foil pouch including the resin impregnated wrap
= Epoxy putty
= Gloves
= Clear plastic clamshell packaging with three color insert and instructions.

This water-activated, fiberglass tape permanently repairs almost any piping including plastic, copper, steel, galvanized, rubber and tile pipe. Will even work underwater! It contains no harmful solvents and is approved for use with potable water. Each package comes pre-mixed and pre-measured to insure a minimum of 8 complete wraps around a pipe (enough for high pressure applications up to 300 psi).

POW-R WRAP+ is an industrial strength pipe and hose repair kit. No tools needed ! Water activated fiberglass tape sets like steel. Repairs almost any surface permanently! Copper. Steel. Galvanized pipe. All plastic pipes. Rubber. Cement. Meets EPA requirements for drinking water. Strong and economical. Works on virtually every kind of pipe. An easy alternative to traditional methods such as cementing, soldering, welding, sleeving and replacement. Works on wet, dry, clean and dirty or corroded pipes. Even under water, fresh or salt!! Ready to use! Pre-mixed. Pre-measured. Cures in 30 minutes at 70ºF / 21ºC.

POW-R WRAP+ is ideal for all fluid bearing pipes and hoses: Water. Steam. Air. Gas. Sewage. Fuel. Hydraulics. Recommended for structural repairs to brackets, fencing, support, exhausts& mufflers and tools. Contains no harmful solvents. Can be used on water and food service lines. Chemically resistant to diesel fuel, petroleum products, halocarbon, and (after curing) alcohols.

Technical Information:
= Form - Impregnated Fiberglass Cloth
= Color - Grey
= Fabrication Method - Wet Lay-up
= Number of Wraps Required - 8 (min) for High Pressure
= Cure cycle @ 70ºF / 21ºC - 30 minutes (wet)
= Hardness v cured laminate - 53 Barcol
= Heat resistance - 1197ºF / 647ºC
= Dielectric Strength - 16,969
= Line pressures - 600 PSI / 40 KPA
= Shelf life - Unlimited when properly stored

POW-R WRAP+ was developed as a simple, user-friendly method of repairing leaks and breaks in water lines. However, upon its introduction to the marketplace, many more uses for POW-R WRAP+ became apparent. The POW-R WRAP+ kit is now being used throughout the world in plants, factories, ships, schools, oil and gas companies, utility companies, lawn and garden maintenance businesses, hatcheries, wineries, farms and plantations. POW-R Wrap is solving such problems as corrosion prevention, gas line repair, insulation, encapsulation and the strengthening of all types of pipes and hoses.

POW-R WRAP+ - Industrial Strength, Water Activated Fibreglass Tape, Pipe & Hose Repair Kit - 2" x 60" suitable for pipes up to 1 1/2"

The complete kit includes:
• A sealed foil pouch including the resin impregnated wrap
• Epoxy putty
• Gloves
• Clear plastic clamshell packaging with full color insert and instructions.

This water-activated, fiberglass tape permanently repairs almost any piping including plastic, copper, steel, galvanized, rubber and tile pipe. Will even work underwater! It contains no harmful solvents and is approved for use with potable water. Each package comes pre-mixed and pre-measured to insure a minimum of 8 complete wraps around a pipe (enough for high pressure applications up to 300 psi).

POW-R WRAP+ is an industrial strength pipe and hose repair kit. No tools needed ! Water activated fiberglass tape sets like steel. Repairs almost any surface permanently! Copper. Steel. Galvanized pipe. All plastic pipes. Rubber. Cement. Meets EPA requirements for drinking water. Strong and economical. Works on virtually every kind of pipe. An easy alternative to traditional methods such as cementing, soldering, welding, sleeving and replacement. Works on wet, dry, clean and dirty or corroded pipes. Even under water, fresh or salt!! Ready to use! Pre-mixed. Pre-measured. Cures in 30 minutes at 70+ F / 21+ C.

POW-R WRAP+ is ideal for all fluid bearing pipes and hoses: Water. Steam. Air. Gas. Sewage. Fuel. Hydraulics. Recommended for structural repairs to brackets, fencing, support, exhausts& mufflers and tools. Contains no harmful solvents. Can be used on water and food service lines. Chemically resistant to diesel fuel, petroleum products, halocarbon, and (after curing) alcohols.

Technical Information:
• Form - Impregnated Fiberglass Cloth
• Color - Grey
• Fabrication Method - Wet Lay-up
• Number of Wraps Required - 8 (min) for High Pressure
• Cure cycle @ 70+F / 21+C - 30 minutes (wet)
• Hardness v cured laminate - 53 Barcol
• Heat resistance - 1197+F / 647+C
• Dielectric Strength - 16,969
• Line pressures - 600 PSI / 40 KPA
• Shelf life - Unlimited when properly stored

POW-R WRAP+ was developed as a simple, user-friendly method of repairing leaks and breaks in water lines. However, upon its introduction to the marketplace, many more uses for POW-R WRAP+ became apparent. The POW-R WRAP+ kit is now being used throughout the world in plants, factories, ships, schools, oil and gas companies, utility companies, lawn and garden maintenance businesses, hatcheries, wineries, farms and plantations. POW-R Wrap is solving such problems as corrosion prevention, gas line repair, insulation, encapsulation and the strengthening of all types of pipes and hoses.

POW-R WRAP+ - Industrial Strength, Water Activated Fibreglass Tape, Pipe & Hose Repair Kit - 3" x 108" suitable for pipes up to 3"

The complete kit includes:
• A sealed foil pouch including the resin impregnated wrap
• Epoxy putty
• Gloves
• Clear plastic clamshell packaging with three color insert and instructions.

This water-activated, fiberglass tape permanently repairs almost any piping including plastic, copper, steel, galvanized, rubber and tile pipe. Will even work underwater! It contains no harmful solvents and is approved for use with potable water. Each package comes pre-mixed and pre-measured to insure a minimum of 8 complete wraps around a pipe (enough for high pressure applications up to 300 psi).

POW-R WRAP+ is an industrial strength pipe and hose repair kit. No tools needed ! Water activated fiberglass tape sets like steel. Repairs almost any surface permanently! Copper. Steel. Galvanized pipe. All plastic pipes. Rubber. Cement. Meets EPA requirements for drinking water. Strong and economical. Works on virtually every kind of pipe. An easy alternative to traditional methods such as cementing, soldering, welding, sleeving and replacement. Works on wet, dry, clean and dirty or corroded pipes. Even under water, fresh or salt!! Ready to use! Pre-mixed. Pre-measured. Cures in 30 minutes at 70ºF / 21ºC.

POW-R WRAP+ is ideal for all fluid bearing pipes and hoses: Water. Steam. Air. Gas. Sewage. Fuel. Hydraulics. Recommended for structural repairs to brackets, fencing, support, exhausts& mufflers and tools. Contains no harmful solvents. Can be used on water and food service lines. Chemically resistant to diesel fuel, petroleum products, halocarbon, and (after curing) alcohols.

Technical Information:
• Form - Impregnated Fiberglass Cloth
• Color - Grey
• Fabrication Method - Wet Lay-up
• Number of Wraps Required - 8 (min) for High Pressure
• Cure cycle @ 70ºF / 21ºC - 30 minutes (wet)
• Hardness v cured laminate - 53 Barcol
• Heat resistance - 1197ºF / 647ºC
• Dielectric Strength - 16,969
• Line pressures - 600 PSI / 40 KPA
• Shelf life - Unlimited when properly stored

POW-R WRAP+ was developed as a simple, user-friendly method of repairing leaks and breaks in water lines. However, upon its introduction to the marketplace, many more uses for POW-R WRAP+ became apparent. The POW-R WRAP+ kit is now being used throughout the world in plants, factories, ships, schools, oil and gas companies, utility companies, lawn and garden maintenance businesses, hatcheries, wineries, farms and plantations. POW-R Wrap is solving such problems as corrosion prevention, gas line repair, insulation, encapsulation and the strengthening of all types of pipes and hoses.

POW-R WRAP+ - Industrial Strength, Water Activated Fibreglass Tape, Pipe & Hose Repair Kit - 4" x 180" suitable for pipes up to 5"

The complete kit includes:
• A sealed foil pouch including the resin impregnated wrap
• Epoxy putty
• Gloves
• Clear plastic clamshell packaging with three color insert and instructions.

This water-activated, fiberglass tape permanently repairs almost any piping including plastic, copper, steel, galvanized, rubber and tile pipe. Will even work underwater! It contains no harmful solvents and is approved for use with potable water. Each package comes pre-mixed and pre-measured to insure a minimum of 8 complete wraps around a pipe (enough for high pressure applications up to 300 psi).

POW-R WRAP+ is an industrial strength pipe and hose repair kit. No tools needed ! Water activated fiberglass tape sets like steel. Repairs almost any surface permanently! Copper. Steel. Galvanized pipe. All plastic pipes. Rubber. Cement. Meets EPA requirements for drinking water. Strong and economical. Works on virtually every kind of pipe. An easy alternative to traditional methods such as cementing, soldering, welding, sleeving and replacement. Works on wet, dry, clean and dirty or corroded pipes. Even under water, fresh or salt!! Ready to use! Pre-mixed. Pre-measured. Cures in 30 minutes at 70ºF / 21ºC.

POW-R WRAP+ is ideal for all fluid bearing pipes and hoses: Water. Steam. Air. Gas. Sewage. Fuel. Hydraulics. Recommended for structural repairs to brackets, fencing, support, exhausts& mufflers and tools. Contains no harmful solvents. Can be used on water and food service lines. Chemically resistant to diesel fuel, petroleum products, halocarbon, and (after curing) alcohols.

Technical Information:
• Form - Impregnated Fiberglass Cloth
• Color - Grey
• Fabrication Method - Wet Lay-up
• Number of Wraps Required - 8 (min) for High Pressure
• Cure cycle @ 70ºF / 21ºC - 30 minutes (wet)
• Hardness v cured laminate - 53 Barcol
• Heat resistance - 1197ºF / 647ºC
• Dielectric Strength - 16,969
• Line pressures - 600 PSI / 40 KPA
• Shelf life - Unlimited when properly stored

POW-R WRAP+ was developed as a simple, user-friendly method of repairing leaks and breaks in water lines. However, upon its introduction to the marketplace, many more uses for POW-R WRAP+ became apparent. The POW-R WRAP+ kit is now being used throughout the world in plants, factories, ships, schools, oil and gas companies, utility companies, lawn and garden maintenance businesses, hatcheries, wineries, farms and plantations. POW-R Wrap is solving such problems as corrosion prevention, gas line repair, insulation, encapsulation and the strengthening of all types of pipes and hoses.

PLASTIC QUICK CONNECTOR SET Durable plastic body 1 male and 1 female connector with shutoff Female with on/off control Fits standard garden hose, outdoor faucets - and watering products Ergo grips for easy connections Blister card 50330 SHUT-OFF QUICK CONNECTOR

Replacement cable for 650 series | 3/8" x 75'

This item can NOT be shipped to these states CA
PRESSURE SWITCH 40/60 pressure settings On at 40 psi and off at 60 psi Quality construction Works on jet pumps or 4" submersibles TC2153P2 40/60 PRESSURE SWITCH

MAGNUS LOW PROFILE TOILET VALVE Low profile toilet fill valve Fits most 2-piece toilets Anti-siphon, adjustable 6" to 12" valve With refill tube and supply nut No float needed Carded 04-4104 FILL PRO TOILET VALVE

Speedway -- 3/8" X100' Replacement Cable For St-440.

POW-R WRAP+ - Industrial Strength, Water Activated Fibreglass Tape, Pipe & Hose Repair Kit - 2" x 30" suitable for pipes up to 3/4"

The complete kit includes:
• A sealed foil pouch including the resin impregnated wrap
• Epoxy putty
• Gloves
• Clear plastic clamshell packaging with full color insert and instructions.

This water-activated, fiberglass tape permanently repairs almost any piping including plastic, copper, steel, galvanized, rubber and tile pipe. Will even work underwater! It contains no harmful solvents and is approved for use with potable water. Each package comes pre-mixed and pre-measured to insure a minimum of 8 complete wraps around a pipe (enough for high pressure applications up to 300 psi).

POW-R WRAP+ is an industrial strength pipe and hose repair kit. No tools needed ! Water activated fiberglass tape sets like steel. Repairs almost any surface permanently! Copper. Steel. Galvanized pipe. All plastic pipes. Rubber. Cement. Meets EPA requirements for drinking water. Strong and economical. Works on virtually every kind of pipe. An easy alternative to traditional methods such as cementing, soldering, welding, sleeving and replacement. Works on wet, dry, clean and dirty or corroded pipes. Even under water, fresh or salt!! Ready to use! Pre-mixed. Pre-measured. Cures in 30 minutes at 70+ F / 21+ C.

POW-R WRAP+ is ideal for all fluid bearing pipes and hoses: Water. Steam. Air. Gas. Sewage. Fuel. Hydraulics. Recommended for structural repairs to brackets, fencing, support, exhausts& mufflers and tools. Contains no harmful solvents. Can be used on water and food service lines. Chemically resistant to diesel fuel, petroleum products, halocarbon, and (after curing) alcohols.

Technical Information:
• Form - Impregnated Fiberglass Cloth
• Color - Grey
• Fabrication Method - Wet Lay-up
• Number of Wraps Required - 8 (min) for High Pressure
• Cure cycle @ 70+F / 21+C - 30 minutes (wet)
• Hardness v cured laminate - 53 Barcoz
• Heat resistance - 1197+F / 647+C
• Dielectric Strength - 16,969
• Line pressures - 600 PSI / 40 KPA
• Shelf life - Unlimited when properly stored

POW-R WRAP+ was developed as a simple, user-friendly method of repairing leaks and breaks in water lines. However, upon its introduction to the marketplace, many more uses for POW-R WRAP+ became apparent. The POW-R WRAP+ kit is now being used throughout the world in plants, factories, ships, schools, oil and gas companies, utility companies, lawn and garden maintenance businesses, hatcheries, wineries, farms and plantations. POW-R Wrap is solving such problems as corrosion prevention, gas line repair, insulation, encapsulation and the strengthening of all types of pipes and hoses.

NO-BURST WASHING MACHINE HOSE Flexible braided stainless-steel Tough & dependable High-pressure hose For hot & cold connections Easily replaces rubber hoses 5 year warranty 9WM72 6 FT. WASHING MACHINE HOSE SIZE:6 Ft. DESC:Sleeve

POW-R WRAP+ - Industrial Strength, Water Activated Fibreglass Tape, Pipe & Hose Repair Kit - 1" x 30" suitable for pipes up to 1/2"

The complete kit includes:
• A sealed foil pouch including the resin impregnated wrap
• Epoxy putty
• Gloves
• Clear plastic clamshell packaging with full color insert and instructions.

This water-activated, fiberglass tape permanently repairs almost any piping including plastic, copper, steel, galvanized, rubber and tile pipe. Will even work underwater! It contains no harmful solvents and is approved for use with potable water. Each package comes pre-mixed and pre-measured to insure a minimum of 8 complete wraps around a pipe (enough for high pressure applications up to 300 psi).

POW-R WRAP+ is an industrial strength pipe and hose repair kit. No tools needed ! Water activated fiberglass tape sets like steel. Repairs almost any surface permanently! Copper. Steel. Galvanized pipe. All plastic pipes. Rubber. Cement. Meets EPA requirements for drinking water. Strong and economical. Works on virtually every kind of pipe. An easy alternative to traditional methods such as cementing, soldering, welding, sleeving and replacement. Works on wet, dry, clean and dirty or corroded pipes. Even under water, fresh or salt!! Ready to use! Pre-mixed. Pre-measured. Cures in 30 minutes at 70+ F / 21+ C.

POW-R WRAP+ is ideal for all fluid bearing pipes and hoses: Water. Steam. Air. Gas. Sewage. Fuel. Hydraulics. Recommended for structural repairs to brackets, fencing, support, exhausts& mufflers and tools. Contains no harmful solvents. Can be used on water and food service lines. Chemically resistant to diesel fuel, petroleum products, halocarbon, and (after curing) alcohols.

Technical Information:
• Form - Impregnated Fiberglass Cloth
• Color - Grey
• Fabrication Method - Wet Lay-up
• Number of Wraps Required - 8 (min) for High Pressure
• Cure cycle @ 70+F / 21+C - 30 minutes (wet)
• Hardness v cured laminate - 53 Barcol
• Heat resistance - 1197+F / 647+C
• Dielectric Strength - 16,969
• Line pressures - 600 PSI / 40 KPA
• Shelf life - Unlimited when properly stored

POW-R WRAP+ was developed as a simple, user-friendly method of repairing leaks and breaks in water lines. However, upon its introduction to the marketplace, many more uses for POW-R WRAP+ became apparent. The POW-R WRAP+ kit is now being used throughout the world in plants, factories, ships, schools, oil and gas companies, utility companies, lawn and garden maintenance businesses, hatcheries, wineries, farms and plantations. POW-R Wrap is solving such problems as corrosion prevention, gas line repair, insulation, encapsulation and the strengthening of all types of pipes and hoses.

Includes all components (Retainer Ring, Slide Ring, O-ring, and High Temperature Gasket) required to assemble to Pro-Flex tubing. Tapped to 1/2" female Size In=3/4 This item cannot be shipped to APO/FPO addresses. Please accept our apologies

NIBCO Half-Turn Frostproof Sillcock|Integral Anti-siphon device|Metal Handwheel|Kalf Turn|Self Draining|Complies to ASSE 1019-C

SEAT ASSEMBLY 2 seat & 2 spring assembly For all faucets except slow close models RP4993 SEAT ASSEMBLY

PVC SCHEDULE 40 BALL VALVE ISO 9002 Rated for 150 PSI at 73 degrees F NSF approved EPDM seats & EPDM O-rings White color Fits both Schedule 40 & 80 pipe Threaded ends comply with ANSI B1.20.1 Solvent ends comply with ASTM D2466 024BV-2 2 SLIP PVC BALL VALVE SIZE:2" DESC:Solvent

REPLACEMENT CARTRIDGE Part brass construction For two-handle kitchen faucets Hot or cold 1224 MOEN 2 HDL REPL CARTRIDGE

POW-R WRAP+ - Industrial Strength, Water Activated Fibreglass Tape, Pipe & Hose Repair Kit - 8" x 540" suitable for pipes up to 20"

The complete kit includes:
= A sealed foil pouch including the resin impregnated wrap
= Epoxy putty
= Gloves
= Corrugated cardboard box packaging with three color insert and instructions.

This water-activated, fiberglass tape permanently repairs almost any piping including plastic, copper, steel, galvanized, rubber and tile pipe. Will even work underwater! It contains no harmful solvents and is approved for use with potable water. Each package comes pre-mixed and pre-measured to insure a minimum of 8 complete wraps around a pipe (enough for high pressure applications up to 300 psi).

POW-R WRAP+ is an industrial strength pipe and hose repair kit. No tools needed ! Water activated fiberglass tape sets like steel. Repairs almost any surface permanently! Copper. Steel. Galvanized pipe. All plastic pipes. Rubber. Cement. Meets EPA requirements for drinking water. Strong and economical. Works on virtually every kind of pipe. An easy alternative to traditional methods such as cementing, soldering, welding, sleeving and replacement. Works on wet, dry, clean and dirty or corroded pipes. Even under water, fresh or salt!! Ready to use! Pre-mixed. Pre-measured. Cures in 30 minutes at 70º F / 21º C.

POW-R WRAP+ is ideal for all fluid bearing pipes and hoses: Water. Steam. Air. Gas. Sewage. Fuel. Hydraulics. Recommended for structural repairs to brackets, fencing, support, exhausts& mufflers and tools. Contains no harmful solvents. Can be used on water and food service lines. Chemically resistant to diesel fuel, petroleum products, halocarbon, and (after curing) alcohols.

Technical Information:
= Form - Impregnated Fiberglass Cloth
= Color - Grey
= Fabrication Method - Wet Lay-up
= Number of Wraps Required - 8 (min) for High Pressure
= Cure cycle @ 70ºF / 21ºC - 30 minutes (wet)
= Hardness v cured laminate - 53 Barcol
= Heat resistance - 1197ºF / 647ºC
= Dielectric Strength - 16,969
= Line pressures - 600 PSI / 40 KPA
= Shelf life - Unlimited when properly stored

POW-R WRAP+ was developed as a simple, user-friendly method of repairing leaks and breaks in water lines. However, upon its introduction to the marketplace, many more uses for POW-R WRAP+ became apparent. The POW-R WRAP+ kit is now being used throughout the world in plants, factories, ships, schools, oil and gas companies, utility companies, lawn and garden maintenance businesses, hatcheries, wineries, farms and plantations. POW-R Wrap is solving such problems as corrosion prevention, gas line repair, insulation, encapsulation and the strengthening of all types of pipes and hoses.

10' power cord, flexible wire construction, pump bracket sold separately. Run current: 13 amps. Start current 90 amps. Liquid temperature 140 degrees F. This item cannot be shipped to APO/FPO addresses. Please accept our apologies

This item can NOT be shipped to these states CA
FLOAT SWITCH Rated at up to 15 amps Piggy-back plug connection For 115-volt operation 8 ft. power cord Ideal for any sump pump Normally open - maintains vessels empty Mounting straps included FP1815BDP2 NON-MERCURY SWITCH

BARB GARDEN HOSE ADAPTER Male hose thread x Barb Economical alternative to brass Works with most flexible plastic tubing Durable plastic construction For sizing, match the inside diameter of - the tubing being used to the outside - diameter of the barb 52680B 1/2 GARDEN HOSE ADAPTER SIZE:1/2"

BARB GARDEN HOSE ADAPTER Male hose thread x Barb Economical alternative to brass Works with most flexible plastic tubing Durable plastic construction For sizing, match the inside diameter of - the tubing being used to the outside - diameter of the barb 52614B 3/4 GARDEN HOSE ADAPTER SIZE:3/4"

Control Valve For Single Lever Cartridge

• 0X8 / JX8 Series Valve Cartridge Sub Assembly

This item can NOT be shipped to these states ca
LEAD-FREE FROST-PROOF YARD HYDRANT Designer series landscape frost-proof hydrant Homeowner preferred floral styling & green - color on cast head and handle 3/4" NPT female inlet 3/4" male hose thread outlet Green polyester powder coated finish Features & installation instructions on box Maximum pressure 120 PSI 5802LF 2 FT. LANDSCAP YARD HYDRANT SIZE:2 Ft. Bury Depth COLOR:Green

• Complete self contained mechanism
• Corrosion resistant components to prolong life of product
• Left hand 90 degree operation
• Ceramic cartridge

REPLACEMENT CARTRIDGE For single-handle kitchen faucets Part brass construction 1225 MOEN REPL CARTRIDGE

CELCON BOILER DRAIN VALVE Rated for 150 PSI at -20 to 180 degrees F For use with hot or cold water 3/4" hose thread outlet Excellent chemical resistance Not for use with compressed air Pipe threads comply with ANSI B1.20.1 Hose threads comply with ANSI B1.20.7 53029 3/4 MIP BOILER DRAIN SIZE:3/4" MIP x MHT COLOR: